| A | B |
|---|
| When using the hand held power grinder, you should | place the item to be worked on in a vise |
| long hair can become entangled in a power tool if not tied back. | True |
| When using a battery operated scroll or jig saw, you should ___________________________________ before changing the blade. | remove the battery |
| Use the ___power tool should be used to cut a 4 foot x 8 foot sheet of plywood in half. | table saw |
| The following power tool should be used to cut a circular wheel out of a small piece of 1/4" plywood | band saw |
| The following power tool should be used to make a 7/16" hole in a 2x2 board. | drill press |
| The following power tool should be used to cut 2 foot pieces of a 1x2 aluminum barstock. | metal cutting band saw |
| The following power tool should be used to cut 2 foot pieces of a 2x4 board. | miter saw |
| Before you turn on the scroll saw, be sure that the _____________is properly adjusted to keep the blade from bending or breaking. | saw blade tension |
| Use only the ________ when you change bits, cutters, or attachments. | proper wrenches |
| Do not place your fingers closer than inch(es) _____ from the path of the saw blade. | 4 |
| Be sure the machine is______ before reaching to pick up a piece of work or anything that is in or near the cutting path of the blade. | at a full stop |
| If the material is bowed, twisted, or warped,________ . | do not cut it |
| Always be sure your work is held firmly against the ______ . | fence |
| Large drills should be run__________ . | at slow speeds |
| ______ stop revolving work by grabbing it. Turn off the machine and step away. | Never |
| Clamp your material to the table or use a drill press vise to keep the drill from ____. | catching your work |
| Never hold small work ________ while drilling. | in your hands |
| ________ leave a chuck key in the chuck socket. | Never |
| Every student must obtain permission from the instructor _________ the portable circular saw. | prior to using |
| All saws must be unplugged or batteries removedfrom the power source when _________ | changing the blade |
| Before starting your cutting operation, make sure the electric power cord will not come in contact with ________. | the moving blade |
| The portable circular saw is designed to cut _______ which can be square or beveled from the top surface of the stock to be cut. | only straight lines |
| If the portable circular saw has a three-prong plug, make sure each prong is in good working condition and _______. | not broken off or loose |
| Do not put your fingers closer than _________ from the blade. | two inches |
| Do not place your hands ____________ the blade while cutting stock. | directly in line with |
| _______ before backing out of a cut. This avoids pulling the blade off its wheels. | Turn off the power |
| To avoid bending and breaking a blade and damaging your work, you should not twist or bend the saw blade with your stock. Make __________ before sawing sharp curves and never use extreme force to cut your material. | relief cuts |
| If the blade breaks or comes off the wheels: shut off the power, stand clear ____________________, and do not open the wheel guards. | let the machine coast to a complete stop |
| Do not _______________ a moving bandsaw blade. | reach around |
| Never try to clean off the bandsaw table with your hands when the saw is running. If scraps and/or cut stock need to be cleared away, _______________ to remove stock away from the moving blade. | use a piece of scrap material at least 10 inches long |
| Always wait for the machine to achieve ______________ before using it, unless otherwise stated in specific machine's safety instructions. | full speed |
| Never hold material in your _________ while cutting with a knife or chisel. | hand |
| ___________all portable electric hand tools before any adjustments are made. | Unplug |
| Long pieces of material should be carried by having a student ________. | at each end |
| Do not ____________ any machine that is in motion. | stand near or lean on |
| Make all measurements on your work while the machine is at ________________. | a dead stop |
| You must never _____________ a machine for another person. | start or stop |
| Never _________ a machine unless you are going to use it. | turn on |
| If a hammer has a loose head, ____________. | do not use it |
| ____________ all machines when you are through using them, putting scraps in the proper place, not on the floor. | Clean off |
| All special set-ups must be inspected and approved __________ the machine is turned on and used. | by the teacher before |
| All tools must be removed from a machine ______________ the power is turned on. | before |
| You must keep all ____________ in place while the machine is running. | safety guards |
| _____annoy or distract the attention of anyone operating a machine. | do not |
| Always _____________ any machine before leaving it. | stop |
| Do not use any machines, hand tools, or portable electric tools on any _______________________. | unapproved projects |
| If you are shocked while plugging in or using a piece of equipment, stop, do not continue working, and immediately ___________. | tell the teacher |
| Make sure all plugs and power cords are ___________before using any piece of equipment or portable electric tools. | not damaged and in proper working order |
| To remove a power cord from an outlet, you should ____________. | pull the plug |
| Carry tools so that the sharp edges are pointed ____________ and away from your body. | downward |
| Return all tools that you are not using to the _________________. | proper storage area |
| You must never leave any tools or materials of any kind lying on the ___________. | floor |
| Any spills must be cleaned up _____. | immediately |
| You must never ____________ anything in the lab. | throw or eat |
| Never put or carry nails, screws, or other objects in your _________. | mouth |
| Do not lift heavy objects beyond your strength. Ask ___________ for assistance. | teacher |
| ______________ are provided for dusty or toxic atmospheric conditions, such as spray finishing, sanding, sawing, and lathe work. | particle masks |
| You must have all loose clothing_________________ before operating any machine. All loose jewelry including rings must also be removed and hair must be tied back. | tightly fastened or removed |
| Everyone must use _______________whenever anyone is working in the shop. | approved eye protection |
| _________________ is to be operated while the teacher is out of the room. | Absolutely no machine |
| Step 1 for operation of a fire extinguisher | Pull the Pin |
| Step 2 of operation of a fire extinguisher | Aim at the base of the fire |
| 3rd step of operation of a fire extinguisher | Squeeze the trigger |
| 4th step of operation of a fire extinguisher | Sweep back and forth |
